The Most Hilarious Complaints We've Been Hearing About Door Lock Change

How to Do a Door Lock Change

Door lock replacement is an easy and inexpensive method to boost your home's security. However, the procedure is not for everyone. It requires some skill and perseverance.

The cylinder is located within the knob body. The cylinder recognizes the key when it is put into the lock.

Remove the old lock

The first step to replace the door lock is to remove the old one. It's a relatively simple process, but you must keep a few things in your mind. Make sure that the new lock fits your door. This will ensure that it fits properly and doesn't leave a gap in the latch or deadbolt plug.

After you have removed the latch plate, you will have to look for two bolts or screws on the inside of casing which are holding the casing in place with the lock halves. Unscrew them using a screwdriver, then remove the lock from the door. If you have a mortise lock, there may be a set screw located at the base of the handle that holds it to the spindle. Make use of a screwdriver for removing the screw, and then take out the doorknobs.

You must also remove the deadbolt latch and latch plug from the hole in the door jamb. Install your new lock. If you are replacing a mortise lock, you must also measure the distance between the lock case and the door's edge to ensure that your new lock will fit.

Many reasons could cause you to replace your door lock, such as believing that someone else has the key or welcoming an incoming roommate. You can save money if you remove the lock yourself, instead of hiring a professional. The process is easier than many people imagine and can be completed in just a few minutes.

Begin by getting rid of the handle and trim from your door. Then, pull  double glazing window locks repairs  using a screwdriver that is flat. You will be able to pull off most of it, and in some cases the handles could come off completely. The next step is to look for a hole on the inside of the handle and then insert an unstraightened clip into it. This will activate the release mechanism and allow you to remove the handle from the door. Look for a small tab in the interior of the lock and push it with a screwdriver that is flat. After the spindle has been removed, you can remove the housing and the cylinder.

The choice of a new locking system

You have many options when it comes time to pick the right lock. Look at different types of locks and choose one that is compatible with the style of your door. Think about the backset (the distance between the door's edge and the center of the lock hole) and the cross bore (small hole in the frame of the door frame). Also, be sure to choose a lock that will fit the door thickness and swing.

The majority of door locks are assessed by BHMA and the American National Standards Institute to give you an idea of how well they stand up to use and how difficult to disable or pick. A grade 3 lock might be a good choice for a tranquil suburban apartment complex, whereas an entry grade lock could hold up better to the traffic near a busy retail storefront on a busy street.

Most smart door locks require digital code to open. If you're concerned about hacking or other security concerns, consult with a professional locksmith or the local police department to get advice.

Replace the cylinder

If the cylinder of your door lock is damaged or broken you can repair it in just a few minutes using a simple DIY project. It is crucial to choose the right cylinder and follow the instructions. First, take off the handle or knob if it is present. Then using a screwdriver remove the trim that is around the lock cylinder. After the trim has been removed, you can remove the screws that hold the cylinder in place using a flathead. The cylinder is then gently pulled out of the door.

Make sure you measure the length of the new cylinder prior to installing it. Find the distance from the center to the right and left sides of the cylinder with an instrument. Then, you can purchase a new cylinder with the same measurements. This will prevent cylinders from snapping when doors are kicked or the key becomes stuck inside.

Insert the replacement cylinder in the door, and then turn the key. This will align the cylinder with the carriage that is usually located on the outside of your lock. After that, you can loosen the set screw that should be just a few turns in the head. If there is a screw located on the edge of the case, which holds the door, you will need to remove it.

After removing the lock cylinder, you can replace it with a new lock by slipping the new cylinder into the case and tightening the set screw. You should also reinstall the bracket that connects the cylinder with the stem for the lock indicator that you can do by pulling up three small tabs on back of the cylinder using needle-nose pliers. Attach the smaller bracket to the cylinder's back. Then, you must put back in the strike plate and latch plate as well as the retaining ring that is connected to the top lock the cylinder.

Installing the new lock

If you're replacing an old lock, you must begin by measuring the width of your door. Most locksets for residential use come with a thickness of 3/8 inch to 1 3/4 inches. If your door is more than 1 3/8 to 1 3/4 inches, you'll need a thicker door kit. This will include longer screws, or an extension for the spindle or a longer tail piece for door knobs.

The majority of locks come with a detailed installation guide to aid you. Before you begin, read the instructions to ensure you have followed all the steps. The booklet will give you a clear idea of the level of skill that is required to complete the task. You might want to ask a person who has experience changing locks for help if you are changing locks for the first time.

Before installing the new lock it is a good idea to cover the openings with tape the old hardware. This will stop the screws from falling through the holes and will also protect any tiles you might have put in. It also protects against potential damage from rust dirt, and grime. SECURAM Touch comes with a strip painter's tape that is intended to be used for this purpose, but you can also use gaffer's tape as well as masking tape in the event that you have it.

After removing the screws that hold the lock's inner half to the exterior then remove the lock immediately. This must be done quickly to avoid the lock from accidentally closing and harming the mechanism.

If your new lock is equipped with an internal latch bolt, insert the new bolt into the upper cross bore. Be sure to put it in the correct place as marked by an arrow on the faceplate. Then, screw the latch plate onto the bolt.

Screw the deadbolt to the jamb on the door. Check the deadbolt several times by throwing it to ensure it is extending into the strike plate. If you're using an electronic smart lock, be sure to follow the included instructions for programming it. This requires downloading an app and registering your email address, confirming your identity, and accessing the wireless network to connect your device.